TEST MODE PROCEDURE
Troubleshooting · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.

- NOTICE:
- Before releasing the parking brake, move the shift lever to the P position for safety.
- HINT:
- When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light comes on.
When the ignition switch on (IG), check that the ABS, VSC (without multi information display), BRAKE warning lights, and master caution, SLIP indicator lights come on for approximately 3 seconds.
- HINT:
- If the skid control ECU stores any DTCs, the ABS, BRAKE, VSC warning (without multi information display) lights, and SLIP indicator light come on.
- If the indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
Trouble Area
See procedure
ABS warning light (Remains on)
Click here
ABS warning light (Does not come on)
Click here
BRAKE warning light (Remains on)
Click here
BRAKE warning light (Does not come on)
Click here
VSC warning light (Remains on)
Click here
VSC warning light (Does not come on)
Click here
SLIP indicator light (Remains on)
Click here
SLIP indicator light (Does not come on)
Click here
| SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (INTELLIGENT TESTER) |
- HINT:
- DTCs are stored if any malfunctions are detected during each sensor check.
Procedure to enter Test Mode.

Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Check that the steering wheel is centered and move the shift lever to the P position.
Turn the ignition switch on (IG).
Set the intelligent tester to Test Mode (select "Signal Check").

- HINT:
- Refer to the intelligent tester operator's manual for further details.
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

- HINT:
- If the ABS warning light does not blink, inspect the ABS warning light circuit.
Trouble Area
See procedure
ABS warning light (Remains on)
Click here
ABS warning light (Does not come on)
Click here
Check the sensor signal.
Drive the vehicle straight ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off when the brake pedal is depressed.- HINT:
- The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
- The ABS warning light goes off when the sensor signal check has been completed and the brake pedal is depressed.
- The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor signal check.
- The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
Stop the vehicle.
- NOTICE:
- The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
- If the signal check has not been completed, the ABS warning light will blink while driving and the ABS system will not operate.
- The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
Read the DTC(s) by following the tester screen.
- NOTICE:
- If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
- If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.
- If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
- HINT:
- See the list of DTCs (See "DTC of test mode (Signal Check) function").
| SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (SST CHECK WIRE) |
- HINT:
- DTCs are stored if any malfunctions are detected during each sensor check.
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is centered and move the shift lever to the P position.
Using SST, connect terminals TS and CG of the DLC3.

- SST
- 09843-18040
Turn the ignition switch on (IG).
Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

- HINT:
- If the ABS warning light does not blink, inspect the TS and CG terminal circuit, and ABS warning light circuit.
Trouble Area
See procedure
TS and CG terminal circuit
Click here
ABS warning light (Remains on)
Click here
ABS warning light circuit (Does not come on)
Click here
Check the sensor signal.
Drive the vehicle straight ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off when the brake pedal is depressed.- HINT:
- The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
- The ABS warning light goes off when the sensor signal check has been completed and the brake pedal is depressed.
- The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor signal check.
- The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
Stop the vehicle.
- NOTICE:
- The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
- If the signal check has not been completed, the ABS warning light will blink while driving and the ABS system will not operate.
- The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
Using SST, connect terminals TC and CG of the DLC3.

- SST
- 09843-18040
Count the number of blinks of the ABS warning light.


- NOTICE:
- If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
- If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.
- If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
- HINT:
- If more than one malfunction is detected at the same time, the lowest numbered code will be displayed first.
- See the list of DTCs (See "DTC of test mode (Signal Check) function").
- If more than one malfunction is detected at the same time, the lowest numbered code will be displayed first.
After performing the check, disconnect the SST from terminals TS and CG, and TC and CG of the DLC3, and turn the ignition switch off.
Turn the ignition switch on (IG) to cancel the Test Mode.
- HINT:
- If the ignition switch is not turned on (IG) after the SST is removed from the DLC3, the previous Test Mode will continue.
- If the ignition switch is turned on (IG) with terminals TS and CG shorted, the previous Test Mode will continue.
- If the ignition switch is not turned on (IG) after the SST is removed from the DLC3, the previous Test Mode will continue.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| Code No. |
Diagnosis |
Trouble Area |
| C1271/71 |
Low output signal of front speed sensor RH |
|
| C1272/72 |
Low output signal of front speed sensor LH |
|
| C1273/73 |
Low output signal of rear speed sensor RH |
|
| C1274/74 |
Low output signal of rear speed sensor LH |
|
| C1275/75 |
Abnormal change in output signal of front speed sensor RH |
|
| C1276/76 |
Abnormal change in output signal of front speed sensor LH |
|
| C1277/77 |
Abnormal change in output signal of rear speed sensor RH |
|
| C1278/78 |
Abnormal change in output signal of rear speed sensor LH |
|
- HINT:
- The codes in this table are output only in Test Mode (signal check).
| ENGINE VARIANT LEARNING |
- Engine variant learning is automatically performed immediately after the Test Mode is entered.
- The ABS, VSC, BRAKE, and SLIP indicators come on for 3 seconds after learning.